1969 Plymouth Sport Satellite

• 5.7 Hemi swap

5.7 Hemi swap

Section 1 - Must have items:

Here is the information on parts needed to refresh the 2008 non-vvt 5.7 Hemi I purchased locally for $700 - From VIN: 1D3HU18208J175865

• MELLING M342HV 20% Additional Volume Over Stock Oil Pump $187
• MDS Delete Kit for 2005-2008 Chrysler Dodge Jeep 5.7L Hemi Engines - w/Mopar 05038784AD Lifters $999
• Holley Gen III Hemi Swap Oil Pan - Mid-Sump Non-VVT Part # 302-60 $493.95
•  Jegs Heavy-Duty SFI Flexplate adapts Mopar, Jeep 5.7L, 6.1L; Mod Hemi to TF727, TF904 Transmission $106.99
• Gen III Hemi Torqueflite Throttle Pressure System w/Cable Operated Throttle Body (613350R)
• BBK Dodge Hemi 5.7 6.1 6.4 85mm Cable Drive Swap Throttle Body $409.99
• Hemi Standalone run Harness $1527
• Holley Mid-Mount Complete Accessory System Part #20.290 $3350
• Schumacher 66-72 B-Body V8 K-Member to Gen 3 Mopar Hemi motor mounts $399
• Gen 3 Hemi Oil Filter Block-Off Plate $99
• Remote oil filter kit -TBD
• TTI Headers - TBD
• Full dual exhaust with H-Pipe
• Borgeson Steering box $660.45
• Cold-Case radiator and fans (TBD)
• Fuel Tank for EFI (TBD-possible options to modify existing tank).
  
  
  Section 2 - Wanted items:
• American-Autowire Classic Update wiring Kit - 1968-70 Mopar B Body 
• Vintage Air - 1969-70 Mopar B-Body with Factory Air GEN 5® SureFit® Complete Kit $2454
• 1966-70 Mopar B-body TREMEC TKX 5 Speed Pro Fit Kit $4485.95
• Lakewood Mopar Small Block and GEN III Hemi Aluminum Bell Housing Ford TKO/TKX $587.95
• MalwoodUSA 1966-70 B-BODY MOPAR Under-Dash Hydraulics Clutch Pedal Kit $625
• Hydraulic Throw Out Bearing for TKX $459
• 6.1L HEMI SRT Intake Manifold - Aluminum (Used ~$500-700)
• 
  
  Section 3 - Shop work before engine can be disassembled. 
  I have a 2015 5.7 Hemi that I bought seized (#8 rod bearing). To free up my engine stand I needed a way to store the extra HEMI for future rebuild. I found a YouTube video outlining how to build an engine cradle from 2x8 Lumber and an Harbor Freight furniture dolly. 
  Purchased one 30x16 dolly $17
  8ft of 2x8 Douglas Fir lumber $12.37
  Total cost about $30 for a quick home built engine cradle.
  
  

Unloading the new to me used 2008 5.7 hemi.

Intake and spark plugs pulled:

Rented a tool from AutoZone to pull the harmonic balancer. It was same one I had used to pull the 2015 Hemi balancer. Did not work. The 2008 truck balancer is a different design and does not work with any standard puller. Had to order a set of puller fingers to fit. They will arrive by end of month hopefully: Lisle - Harmonic Balancer Puller 3 Jaw Set Hemi (54870)